Drips Over A Work Bay
Water drips onto the floor of a garage bay during heavy rain.
Fasteners on the metal roof have backed out, or a panel lap over the bay has opened.

As a Union commercial roofing contractor, we roof shops, service garages, and small commercial buildings on rural lots, with deliveries and staging planned before the crew arrives.
Union commercial roofing jobs are often on buildings set back on rural roads, with gravel drives, tight turnarounds, and no room for a big truck to wait. Getting materials there takes as much planning as the roof itself. A wet spring drive can stop a loaded truck, so timing matters too.
We check the drive, the turnaround, and where a dumpster and lift can sit before the job is priced. Deliveries are timed so the crew has what it needs on hand and the roof gets done in fewer trips. Fewer trips also means less wear on your drive and lawn.

Small rural buildings leak in a few common places. These pairs show what owners see and the roof cause.
Water drips onto the floor of a garage bay during heavy rain.
Fasteners on the metal roof have backed out, or a panel lap over the bay has opened.
Thick ice forms at the eaves and water stains the wall below it.
Heat escaping through the roof melts snow that refreezes at the cold edge.
A small stain forms on the ceiling around a vent or flue.
The pipe boot on the roof has cracked and lets water run down the pipe.
Panels rattle or bang on windy days and stains appear after storms.
Fasteners have worked loose along the eaves and gables, letting panels move and water in.
Planning a rural job well shortens it and keeps costs tied to the roof.
Deliveries arrive when the crew needs them, so the roof gets done without long gaps.
New fasteners, laps, and trim stop the drips over work bays and stored equipment.
Insulation and ventilation details reduce heat loss through the roof that feeds ice at the edges.
Every pipe and flue gets a new boot tied into the roof, ending the small ceiling stains.
Rural shops and small commercial buildings take one of these systems.

Standing seam or exposed fastener panels cover sloped shop and garage roofs, shed snow well, and go up quickly once framing is checked.
Commercial Metal Roofing details
Rubber membrane suits small low-slope roofs and additions, with few seams to maintain and flexible flashing at walls.
EPDM Roofing details
Welded white membrane fits flat-roofed offices and stores with rooftop units, and its welded flashings hold at curbs.
TPO Roofing details
Larger production buildings in the area get industrial roofs planned around their fans, ducts, and rooftop equipment.
Industrial Roofing detailsCall and tell us which bay is leaking. We check the fasteners and laps above it first.
Send the address and a note about the drive. We plan deliveries before pricing.
Get A Free EstimateRural jobs follow this order so the crew has what it needs on hand.
We walk the roof, check fasteners, laps, vents, and eaves, and look at the drive and turnaround for trucks.
Roofing material drops, the dumpster, and the lift are scheduled and placed so trucks can get in and out.
Old roofing comes off, repairs are made, and the new roof goes on with materials already on hand.
Debris leaves with the dumpster, the yard is checked for fasteners, and we walk the roof with you.
Notes cover what to watch, such as fasteners and vent boots, and when to schedule the next roof walk.
Is your shop on the far side of the town line? These towns are covered too; for anywhere else, call us or send us a message.
What rural business owners in Union ask us about roof work on shops, garages, and small commercial buildings.
Usually, yes. We check the drive, the turnaround, and the ground before the job, and size delivery trucks and the dumpster to fit.
More roofing questionsHeat from inside melts snow on the roof, and the water refreezes at the cold eave. Better insulation and ventilation reduce that melt.
Often. Metal panels shed snow from sloped roofs, and new fasteners and trim keep work bays dry.
Most commercial reroofs need one. We check with the town building department and pull the permit as part of the job.
Small shop and garage roofs often take a few days once materials are on hand. Planning deliveries ahead keeps the crew from waiting.
Rarely. Panels with rust, bends, or enlarged screw holes leak at the old holes, so we replace them with new panels.
One roof walk and one plan cover both, with metal panels on the sloped part and membrane on the flat section, joined with flashing.
Yes. Small repairs in Union are often scheduled with other work nearby, which keeps travel down and lets us reach the building sooner.
Send the property address and a note about the drive, or call about a leak in a shop or garage.